Activated Alumina Desiccants

Availability: In stock

Sku: RXSOL-19-1905-025

Be the first to review this product

Quick Overview

More effective then ORDINARY alumina. Also refer new tec grade if ur requirement to absorb poisonous gases RXSOL-24-1905-025

Activated alumina is highly porous material; this material can have a surface area significantly over 200 square metres/g. Very suitable for use as a filter of fluoride, arsenic and selenium in drinking water.

Application:

Activated Alumina Desiccants:

Activated Alumina Desiccants is a porous form of aluminum oxide. It has a high surface area which adsorbs vapors without any change in form. Activated Alumina Desiccants  will not soften or disintegrate easily when immersed in water.

Dew points to -40°F and lower may be achieved with Activated Alumina Desiccants  depending on dryer design and operating conditions.

The 1/8” (2-5mm) bead is the size most frequently used in regenerative dryers.

The 3/16” (4-8mm) bead is used when pressure drop and surface area requirements fall between 1/8” and 1/4” material.  It is suitable for most systems.

The 1/4” (5-10mm) bead Activated Alumina Desiccants  is used both as a pre-bed material to support large desiccant beds or as a buffer for silica gel beads. Pressure drop is slightly lower than 1/8” (25mm) material.

If size is not known or specified, the 1/8” (2-5mm) size is usually satisfactory. However, if Activated Alumina Desiccants is used in a regenerative dryer and the desiccant retaining screens cannot be measured, the 1/4” (5-10mm) size should be used as a bed support (6” layer). If at all possible, obtain a sample and measure it  before ordering.

Product Benefits:

  1. High adsorption capacity. With high surface area and excellent pore distribution, Activated Alumina Desiccants  has a high water adsorption capacity. This reduces initial cost, energy consumption and operating costs through smaller bed sizes and/or longer operating cycles.
  2. Low abrasion. Insures less dusting during tower depressurization or loading. Low abrasion means low pressure drop and a reduced chance of plugging the afterfilter.
  3. Resists liquid water. Water slugging due to upstream failure of aftercooler, separators or drain traps will not fracture the alumina beads. The adsorption capacity of the desiccant can be restored after complete regeneration.
  4. High crush strength. High crush strength, which limits dusting, is important during loading of desiccant towers. High crush strength makes alumina effective as a prebed material when used with other types of desiccants.
  5. Uniform bead sizes. Activated Alumina Desiccants is a uniformly sized bead. It provides low pressure drop to minimize channeling and ensures utilization of the full bed column section.

Physical Properties:

1/8” (2-5mm) 3/16”(4-8mm) 1/4” (5-10mm)
Color and form  White  bead  White  bead  White  bead
 Bulk density  48 lbs/Ft3  48 lbs/Ft3  48 lbs/Ft3
 Crush strength  17-30 lbs 145-60 lbs 50-70 lbs
 Surface area  1.74 x 106 sq ft/lb  1.65 x 106 sq ft/lb  1.59 x 106 sq ft/lb
 Static adsorption
Humidity
            –            –              –
100% RH
90% RH
60% RH
10% RH
42.0%
37.5%
21.0%
7.5%
40.0%
35.0%
21.0%
7.0%
36.0%
32.0%
17.5%
6.0%

Dose:

Drier Chemicals manufacturer, importer and exporter of industrial chemicals and desiccants such as silica gel, activated alumina, activated carbon and carbon molecular sieves etc. Click on this link to get Most powerful GAS  absorber.

Note:

Also refer more details of Impregnated Activated Alumina with potassium permagnate KMNO4.

Potassium Permanganate Impregnated Alumina has strong oxidizing property with Potassium Permanganate (KMnO4), it has good efficienty in removing Hydrogen Sulfide(H2S) , Chlorine(Cl2), Formaldehyde(HCHO), Nitric Oxide (NO) & Sulfur Dioxide(SO2) from air.

Additional information

MSDS

Product Name

RXSOL-19-1905-025

Product Type

Activated Alumina Desiccants

CHEMICAL NAME

Aluminum Oxide

Company Details:

RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA

Phone

+91 22 65113333 / 5555 / 9999

Fax

+91 22 2781 1318 :::AOH :0091 9821214367

Email

mail@rxmarine.com

PRODUCT IDENTIFICATION PRODUCT NAME: Activated Alumina 

INGREDIENTS

COMPONENTS
 

CAS NO.

%BY WEIGHT
 

ACGIH TLB        

OSHA PEL

Aluminum oxide 

1333-84-2

<97%

N/D

15 (total dust),

Aluminum silicate

14504-95-1

<0.2%

N/D

5 (respirable) mg/m3

 

 

EYES:

Can cause mild irritation, especially when wet.

SKIN:

Can cause mild irritation.

INHALATION:

Can cause mild upper respiratory tract irritation.

INGESTION:

Can cause mild irritation.

Alumina is a low health risk by inhalation and should be treated as a nuisance dust as specified by the ACGIH. This product contains total silicates at <1% by weight.

EYES:

Flush eyes with plenty of water or saline for at least 15 minutes. Consult a physician.

SKIN:

Wash with soap and water for at least 15 minutes. Consult a physician if irritation persists.

INHALATION:

Remove to fresh air. Check for clear airway, breathing, and presence of pulse. Provide CPR for persons without pulse or respirations. Consult a physician.

INGESTION:

If swallowed, dilute by drinking large amounts of water. Never give,anything by mouth to a convulsing or unconscious person. Do not induce vomiting. Consult a physician.

SUITABLE EXTINGUISHING AGENTS:

Use fire fighting measures that suit the environment.

PROTECTIVE EQUIPMENT:

Wear self-contained respiratory protective device. Wear fully protective suit.

ACCIDENTAL RELEASE MEASURES:

Person-related safety precautions: Wear protective clothing. 
Measures for environmental protection: No special measures required.
Measures for cleaning/collecting: clean up using dry procedures; avoid dusting.
Additional information: No dangerous substances are released.

Alumina is a low health risk by inhalation and should be treated as a nuisance dust as specified by the ACGIH. This product contains total silicates at <1% by weight.

HANDLING:
 

Ensure good ventilation/exhaust at the workplace. Prevent formation of dust. Provide suction extractors if dust is formed.

Protection against explosions and fires:

No special measures required.

STORAGE:

Keep material dry. Storage in one common storage facility is not required.

Personal protective equipment. Do not inhale dust. Avoid contact with the eyes. Use suitable respiratory protective device in case of insufficient ventilation.
Short term filter device: Filter P2. Protection of hands: impervious gloves. Eye protection: Safety glasses.

APPEARANCE:

Off-white, crystalline or gelatinous granules, pellets.

BOILING POINT:

 Undetermined

FREEZING POINT:

3,700°F (2038°C)

VAPOR PRESSURE:

 Not applicable

AUTOIGNITING:

Product is not self igniting

SPECIFIC GRAVITY:

3.2

DENSITY:

Loose Bulk: 39-52 lb/ft (0.62-0.83 g/cm ).

pH:

10% in water 9.4-10.1

ODOR:

Characteristic

CHEMICAL STABILITY CONDITIONS TO AVOID

A rise in temperature may result from contact with water.

INCOMPATIBILITY

None.

HAZARDOUS DECCSIPOSITION PRODUCTS

None if used according to specifications.

HAZARDOUS POLYMERIZATION:

None. Non-corrosive.

 N/A

 N/A

Collect in containers, bags, or covered dumpster boxes. If reuse or recycling is not possible, material may be disposed of at an industrial landfill.

Waste disposal key: 16 03 01  513 05
Disposal must be made according to official regulations.

 N/A

 NA

the above information is accurate to the best of our knowledge.however, since data, safety standards, and government regulations are subject
to change and the conditions of handling and use, or misuse, are beyond our control, seller makes no warranty, either express or implied, with
respect to the completeness  or  continuing  accuracy of the  information  contained  herein and disclaims all liability for reliance thereon. User
should satisfy himself that he has all current data relevant to his particular use.

Reviews

There are no reviews yet.

Be the first to review “Activated Alumina Desiccants”

52 − = 48

custom contents goes here
Top
WhatsApp chat